This post down below about A Step-by-Step Guide to Installing a Bathtub is exceptionally fascinating. Read it yourself and see what you think of it.
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the task can relocate quickly; if you need to open a wall to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and are comfortable trying it. Instead of working with a specialist to take over a halfway-completed task, it is better to take into consideration using one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and do not require to change the setup of your previous water system pipelines.
Your tools and also material list should consist of the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible faucet ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of removing the existing taps can be rather problematic because of the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bathtub till the level checks out level.
To install taps, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water as well as check all joints and brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub as well as likewise inspect the overflow outlet and also the typical outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bath tub has actually been used at least when as this will resolve it right into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in place in between the tap as well as the sink. Secure the tap in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous kind should be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall in between the bathroom and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on a different web page. Do you know somebody else who is interested by the niche? Take a moment to share it. Thanks for taking the time to read it.
Book With Us Today!